自上料攪拌車行駛中水溫過高怎么辦？
有這樣一種情況，就是我們的駕駛員在駕駛自上料攪拌車的時分會常常發覺這樣的一種現象，那就是水的溫度過高，這個到底什么情況呢？要怎么處理呢？負責中科攪拌車的小編幫你來！
There is such a situation, that is, our drivers will often find such a phenomenon when driving the self loading mixer, that is, the water temperature is too high. What is the situation? How to deal with it? Responsible for the price of China Science mixer to help you solve!
一、燃燒發起車時的操作過程不正確。
1、 The operation process of the combustion engine is not correct.
二、冷卻介質缺少：①防凍液：好車要求一年四季都要加注防凍液；②水或蒸餾水：暫時代用；③水箱蓋漏水。
2、 Lack of cooling medium: ① antifreeze: good cars require filling antifreeze all the year round; ② water or distilled water: temporary substitution; ③ water tank cover leakage.
三、水泵缺點：葉輪打滑或卡死導致正時皮帶斷掉；葉輪變形。
3、 Disadvantages of water pump: the timing belt is broken due to slipping or jamming of impeller; impeller is deformed.
四、冷卻電扇不轉：冷卻電扇或許由溫控開關控制；也或許由水溫傳感器控制。
4、 The cooling fan doesn't work: the cooling fan may be controlled by a temperature control switch or by a water temperature sensor.
五、水箱堵塞：外部堵塞應用水或氣將臟物除掉；內部堵塞會影響冷卻液的循環，一起會發作壓力，這時會有兩種效果，一種是水箱漏水，另一種是在高速行駛時水溫特別高。
5、 Water tank blockage: external blockage should be removed by water or air; internal blockage will affect the circulation of coolant, and pressure will occur together. At this time, there will be two effects: one is water tank leakage, the other is that the water temperature is extremely high when driving at high speed.
六、汽缸損蝕：燃燒室與水道沖，這時會從排水管排水或排白煙，構成水箱經常性缺水；水道與油道沖（機油有水呈白色）；水道與水道沖，構成缸體散熱不良，尤其在高速時影響更大。
6、 Cylinder erosion: when the combustion chamber and water channel are flushed, the water will be drained from the drain pipe or white smoke will be discharged, which will cause frequent water shortage in the water tank; the water channel and oil channel will flush (the oil will be white with water); the water channel and water channel will cause poor heat dissipation of the cylinder block, especially at high speed.
七、節溫器損壞：如想拆掉節溫器，此時應把小循環堵上，這樣可以保證冷卻液全部由水箱散熱；裝新節溫器時應留心是否有過水孔。
7、 Thermostat damage: if you want to remove the thermostat, plug the small circulation at this time, so as to ensure that the cooling liquid is completely dissipated by the water tank; when installing a new thermostat, pay attention to whether there is a water hole.
假設在駕御的時分發現了水溫過高就要靠邊泊車，但不要當即熄火。因?yàn)槔鋮s液的溫度現已很高，降溫才干已達到限度，這時假設當即熄火，歡娛的冷卻液也就間斷了循環。過高的溫度得不到冷卻，發起機也是難以承受的。假設先讓發起機怠速作業一會兒，不斷循環的冷卻液仍是可以減輕高溫對發起機的影響。
If you find that the water temperature is too high when driving, you should pull over and park, but don't turn off the engine immediately. Because the temperature of the coolant is now very high, the cooling ability has reached the limit. At this time, if the engine is turned off immediately, the happy coolant will be interrupted circulation. If the temperature is too high to be cooled, the engine is hard to bear. If the engine is allowed to idle for a while, the circulating coolant can still reduce the influence of high temperature on the engine.
自上料攪拌車水溫過高的核心原因大概為上面介紹的內容，還有就是必定要留心在水的溫度過高情況下千萬千萬不要滅火，否則就會對發起機構成常性的損害。以上就是負責中科攪拌車http://www.jbckj.cn的小編來針對自上料攪拌車在形式中溫度過高的方案，希望能幫到您！
Since the feeding mixer water temperature is too high, the core reason is probably the content described above, and it is necessary to pay attention to do not extinguish the fire when the water temperature is too high, otherwise it will cause regular damage to the starter. The above is responsible for the price of Zhongke mixer http://www.jbckj.cn From the small series to feed mixer in the form of high temperature solutions, hope to help you!
