全自動攪拌車開工干活要注重什么事項
1、檢查、發現問題并排除故障
1. Check, identify problems, and troubleshoot
全自動攪拌車怕跑在路上，罐子不轉了，一般來說裝滿混凝土的罐子一般停管不能超過2小時，C40級以上的混凝土罐子就一直不能停。
The fully automatic mixer truck is afraid of running on the road and the tank won't rotate. Generally speaking, the tank filled with concrete can't be stopped for more than 2 hours, and concrete tanks above C40 level cannot be stopped for a long time.
卡車啟動后，讓攪拌罐低速轉動，檢查胎壓，看是否有漏氣的輪胎，檢查輪胎內是否有石塊、釘子等東西卡在里面，并及時清理干凈。
After the truck starts, let the mixing tank rotate at low speed, check the tire pressure, see if there are any leaking tires, check if there are stones, nails, and other things stuck inside the tires, and clean them in a timely manner.
全自動攪拌車廠家提醒您要檢查側燈，確保照在輪胎邊緣，因為施工現場經常會有鋼筋等雜物隨意堆積，胎側薄弱。
The manufacturer of the fully automatic mixing truck reminds you to check the side lights to ensure that they are shining on the edge of the tires, as there are often steel bars and other debris piled up randomly at the construction site, resulting in weak tire sides.
2、確保水箱中有足夠的水和減水劑
2. Ensure that there is sufficient water and water reducing agent in the water tank
由于各種原因，當材料過于干燥，不加水無法排出時，減水劑是一種救命稻草，可以保證混凝土的流動性。
Due to various reasons, when the material is too dry and cannot be discharged without adding water, water reducing agents are a life-saving straw that can ensure the fluidity of concrete.
3、確認攪拌罐處于停止?fàn)顟B(tài)
3. Confirm that the mixing tank is in a stopped state
因為全自動攪拌車發動機啟動時，萬一攪拌罐高速旋轉，瞬時受力會很大，會對減速器和泵電機系統造成傷害。
Because when the engine of the fully automatic mixing truck starts, if the mixing tank rotates at high speed, the instantaneous force will be very large, which will cause damage to the reducer and pump motor system.
1. 鎖定駕駛室內防逆轉手柄，以防載物排在道上。
1. Lock the anti reverse handle inside the driver's cab to prevent loads from lining up on the road.
2. 將定位手柄卡入定位卡盤內，鎖止機構卡住伸縮總成，固定滑料槽。
2. Insert the positioning handle into the positioning chuck, lock the telescopic assembly with the locking mechanism, and fix the sliding groove.
3.車尾操作手柄應置于“攪動”檔內；油門置于怠速位置。
3. The rear operating handle should be placed in the "stirring" position; Place the throttle in the idle position.
4.車輛在行駛過程中，關閉為水箱供氣的氣源閥門，以免影響車輛的制動性。
4. During driving, close the air supply valve for the water tank to avoid affecting the braking performance of the vehicle.
5.運行時，加長滑料槽必須翻轉卸下，放置在擋泥板的專用位置并鎖定。以防擺動傷人或影響其它車輛的運行。
5. During operation, the extended sliding chute must be overturned and removed, placed in a dedicated position on the mudguard and locked. To prevent swinging from injuring people or affecting the operation of other vehicles.
6.全自動攪拌車穿越橋、洞、庫等設施時，必須要注意通過高度的尺寸，以免發生碰撞造成傷害。
When fully automatic mixer trucks pass through facilities such as bridges, tunnels, and warehouses, attention must be paid to the size of the passing height to avoid collisions and injuries.
全自動攪拌車開工干活要注重的事項就講解到這里了，希望能夠給您好的幫助，更多事項就來我們網站http://www.jbckj.cn咨詢！
That's all we need to pay attention to when starting work on a fully automatic mixer truck. We hope it can be helpful to you. For more details, please visit our website http://www.jbckj.cn consulting service
