當前位置：首頁 »新聞中心 » 常見問題自動上料攪拌車出車前的檢查事項有哪些？

自動上料攪拌車出車前的檢查事項有哪些？

來源：http://www.jbckj.cn 瀏覽：0發表時間：2020-12-03

1.確認自動上料攪拌車攪拌罐處于停止?fàn)顟B(tài)，因?yàn)榘l(fā)動機啟動時萬一罐子處于高速旋轉狀態，瞬間的力會很大的，會損傷減速機。

1. Make sure that the mixing tank of the automatic feeding mixer is in the stop state, because if the tank is in the high-speed rotation state when the engine is started, the instantaneous force will be great and the reducer will be damaged.

2.要保證水箱里有足夠的水，有減水劑，因?yàn)楦鞣N原因料太干，沒有水添加放不出料的時候，減水劑就是救命稻草了。

Water reducing agent is not enough when adding water reducing agent into the water tank.

3.自動上料攪拌車點火之前先檢查機油、防凍液、潤滑油和冷卻水等，發現不足時，應重新進行添加。

3. Check the engine oil, antifreeze, lubricating oil and cooling water before the ignition of the automatic feeding mixer, and add them again if they are insufficient.
中科攪拌車

4.還要檢查自動上料攪拌車的燈光，尤其是腰燈，務必保證照著輪胎邊緣，工地會經常亂堆放鋼筋之類的東西，而胎側是較為薄弱的。

4. Also check the light of the automatic feeding mixer, especially the waist light. Make sure that the light is shining on the edge of the tire. The construction site will often stack reinforcement and other things, and the sidewall is relatively weak.

5.還應用抹布擦干凈兩邊的后視鏡、窗戶玻璃，工地路況復雜，光線不好，視線一定要有保證。

5. Clean the rear-view mirror and window glass on both sides with dishcloth. The road conditions on the construction site are complex and the light is not good. The line of sight must be guaranteed.

6.車子啟動后，讓罐子低速旋轉，圍繞著車檢查輪胎氣壓，是否有漏氣的胎，再用螺絲刀剔掉在胎縫里的石子。

6. After the car starts, let the jar rotate at a low speed. Check the tire pressure around the car to see if there is a flat tire. Then use a screwdriver to remove the stones in the tire seams.

下一篇：自上料攪拌車行駛中水溫過高怎么辦？上一篇：混凝土攪拌車卸料時的注意事項！